Can You Use A Roller To Apply Thompson’S Water Seal?

How long does Thompson’s Water Seal last?

10 yearsIf applied correctly, Water Seal will last up to 10 years..

What is the best way to apply deck sealer?

Apply the deck sealer with a natural bristle brush. A roller is faster, but brushing helps force the sealer into open pores and grain. Make sure to get the sealer into joints where two boards butt together. Apply the deck sealer to three or four boards at once, working their entire length.

What temperature do you apply Thompson’s Water Seal?

Be sure that both surface and air temperatures are above 50°F during application and remain above 40°F for 48 hours after application. Do not apply product if rain is forecasted within 24 hours of application.

Is it too late to seal my deck?

As a general rule, expect to wait approximately 30 days before scheduling professional deck sealing. However, in the case of intense wood grains such as cedar and mahogany, you may want to seal the deck earlier — perhaps within one or two weeks.

Is Thompson Water Seal oil or water based?

Thompson’s® WaterSeal® Penetrating Timber Oil is an oil-based product that provides protection by penetrating into wood pores and sealing out water infiltration. Thompson’s® WaterSeal® Waterproofing Stains are water-based products that have film-forming properties to protect the wood by repelling water.

What is the best way to apply Thompson’s Water Seal?

All Thompson’s WaterSeal products are DIY-friendly, and most need only a single application on a clean, dry deck. You can apply some products with a garden sprayer or paint roller, but for classic deck stain, a paint pad on an extension pole is best.

Can you use a roller to seal a deck?

DO use proper tools and technique for sealing a deck. Deck sealant can be applied using a roller, a paint brush, or even a paint sprayer. You can work from a standing position with a pole or on your hands and knees (kneepads highly recommended).

What type of roller do you use to seal a deck?

3/8 – 1/2-inch roller covers are best for lightly textured surfaces. When applying stain with a roller on rough surfaces, like weathered exterior wood, use 3/4-inch or thicker roller covers. Tip: A paint or stain’s manufacturer will list whether a long or heavy nap, or if a short nap will work best.

What happens if you don’t seal your deck?

The bad news is that if the wood is not sealed the lumber will begin to wear at a far faster rate than it would without that protective layer. … But when it happens this wear will be evidenced by greying, as the top layers of the lumber oxidize from sun and rain, and also splintering, warping, rotting, and cracking.

Is it better to spray or brush stain?

The agitation and friction caused by a paint brush will cause the wood to absorb more stain. So if you are spraying or rolling the stain, always back-brush it in with a brush while the stain is still wet; you’ll achieve much better penetration in to the wood.

How many coats does Thompson’s Water Seal have?

Thompson’s WaterSeal Waterproofing Stains. Application: Only one coat is recommended for both Semi –Transparent & Solid. A second coat can be added if more color is desired. Allow the first coat to dry (approximately 2 hours) before second application.

What happens if it rains after applying Thompson’s Water Seal?

Rain will damage the finish of any wet sealer with linseed oil or mineral oil in it. Because it forms a coating, it takes several hours to “set up” (dry) and during that time the sealer is vulnerable.

Is it better to stain or seal a deck?

Many deck companies recommend using a combination stain/sealer product, which is basically a sealer with pigment added. The advantage of this, they say, is the sealer provides additional protection against water and weather damage, while the stain helps reduce fading from UV rays.

What is the best sealant for pressure treated wood?

1. BEST OVERALL: SEAL-ONCE MARINE Penetrating Wood Sealer. SEAL-ONCE MARINE Penetrating Wood Sealer is a clear water-based sealer, but it provides the protection you’d expect from an oil-based stain, penetrating right down into the wood fibers for long-lasting protection against moisture damage and mold growth.

What is the difference between concrete sealer and Waterproofer?

One of the differences between a concrete sealer and a concrete waterproofer (sometimes called penetrating sealer) is that a sealer will form a protective layer over the surface while a waterproofer will penetrate down into the pours of the concrete and the protective layer will form there.

Is Thompson’s Water Seal any good?

5.0 out of 5 stars Love Thompson’s Water Seal with the harvest gold color! Basically, it takes your weather worn fence and restores it back to almost new looking boards, plus protecting it from the elements. I used my spray gun to apply, and a little goes a long way. Obviously, you can use a brush to apply it as well.

Is it better to stain a deck with a brush or roller?

You should use a roller brush or sprayer to apply a steady coat of quality stain, such as Olympic Elite stains or Olympic MAXIMUM stains. If you see that too much wood stain has been used in an area, use a roller or brush to fix the imperfections.

Can you use Thompson Water Seal on pressure treated wood?

However, most of the water-repellent sealers sold at home centers, paint stores and lumber yards are suitable for pressure-treated wood as well as other outdoor woods such as cedar and redwood. The directions for some, such as Thompson’s Water Seal, specify pressure-treated wood as a suitable use.